Tips for Drywall Finishing

Tips for Drywall Finishing

Drywall Finishing

Drywall is a panel made of Calcium Sulfate Dihydrate. Sometimes people will add additives to the mixture. However, other times they won’t. The wallboard can also consist of gypsum plaster which is sandwiched in between two sheets of paper. Sheets of the drywall are nailed into wooden studs when it’s complete. Drywall can also be used to beatify and design many aspects of a house. It’s an amalgam that people can shape easily. It’s also not extremely expensive, which makes it accessible.

Before people used drywall, they were using plaster. For many years people were making walls and ceilings by placing layers of wet plaster over wooden strips called laths. The wet plaster eventually hardens and forms walls. If you’re thinking about DIY-ing drywall, then you’ve come to the right place. Read on as we inform you about some of the measures you can take for the perfect Drywall finishing.

1. Check for Undriven Screws and Nails 

Before you start working on finishing the drywall, you should make sure that the screws and nails are driven into the drywall all the way. A telltale metallic click will generally inform you about all the places that a screw or nail is protruding from the face of the wall. The problem with these screws and nails is generally along with the corners, so here’s where you have to take the most care of these screws. Before you begin, you can drive in the screws and nails with either a hammer or a screwdriver.

2. Hammer Nails Slightly Below the Drywall Face

What may seem like properly driven in for you may be underdriven. You want to notice a completely driven nail that has a shallow dimple into the wall when you’re finally finishing up. However, you have to be careful while doing this because an intense hammering can cause the drywall to cave in. A special drywall hammer is perfect for hammering in. However, you can use a regular hammer too.

3. Trim Away Loose Paper With a Utility Knife

The drywall has paper in place too.  If you find that the gypsum core is obliterated in some parts, it’s best to trim away the loose paper in these soft spots. Cutting away these paper strips allows the drywall compound to spread and reach around the soft areas too. If you don’t cut off a loose or torn paper at the right time, it will create bubbles and pokes after the final finishing.

4. Apply a Stain Blocking Primers

While applying and conducting the drywall finishing, there may be some rough fibers that are torn. You should apply a layer of primer so these loose paper fibers can seal in, and the chemicals don’t have to bleed through or stain the finished coat of paint. You can ventilate the room well, and you should wear a vapor-absorbing mask so that you don’t harm your health when you’re using solvent-based primers.

5. Nail the Metal Corner Bead

You should leave 1/8th of an inch from each flange,  so there’s a pocket for some drywall compound. The best test for your perfect positioning is that you’d be able to run your knife along with the bead without meeting a nail bed or scraping against flanges.  You should only use a single length of bead for each corner; otherwise, there can be bumps and creases where the two pieces join. 

6. Fill The Gaps if There Are Any

To fill the gaps, you would need a setting compound that dries easily and hardens rapidly. You should start taping as quickly as it hardens. The setting compound is most often a powder that you mix with water. Most of these compounds are available with 20,45, and 90 minute hardening times. You should keep a window for 20 minutes as it will harden in pain.

7. Use Setting-Type Compound For Deep Fills

You can also use the setting compound for any deep fills if you have any holes that you need to fill. Then, you can use the setting compound for this too.

8. Shave Off the Excess

You can remove the excess material of the setting compound by using a taping knife or a scraper when the compound reaches a thicker consistency. The areas you fill deeply sometimes bulge and grow after they harden, so you want your best to get rid of any excess material that may transpire after drying. 

9. Cover the Nails and Screws with Drywall Mixture

For this purpose, you will have to make the drywall mixture and then paint over the exposed screws and nails with the drywall mixture. Once you’re done with this stage, you can scrape off the excess, remove the tape, sand the compound lightly and get it primed for painting.

For the best drywall finishing, choose Fast Finish Drywall. They are prepared to take on any challenging project that requires their drywall expertise and professionals. Visit the Fast Finish website to learn more.